Engineering Physics 2 - Metallic glasses: preparation, properties and applications (Unit 5)

Anna University

Engineering Physics 2


Metallic glasses: preparation, properties and applications

( Unit : V )


Introduction

clip_image003

Scientist at Yale have developed a new fabrication process using bulk metallic glasses (BMGs), which are "amorphous metals" that can avoid crystalizing when cooled in a specific way. The upshot is that the metal -- while seeming solid -- acts as a slow- flowing liquid, with no structure beyond the atomic level. The BMGs can therefore replace several steps in the chip-stamping process, since they're more durable than silicon, but are more pliable than normal metals. Right now the folks at Yale are making patterns as small as 13nm, with better processes to come.

clip_image002

Electron diffraction image of an enstatite grain before irradiation (left panel) and after complete amorphization (right panel)


An amorphous metal is a metallic material with a disordered atomic-scale structure. In contrast to most metals, which are crystalline and therefore have a highly ordered arrangement of atoms, amorphous alloys are non-crystalline. Materials in which such a disordered structure is produced directly from the liquid state during cooling are called "glasses", and so amorphous metals are commonly referred to as "metallic glasses" or "glassy metals". However, there are several other ways in which amorphous metals can be produced, including physical vapor deposition, solid-state reaction, ion irradiation, melt spinning, and mechanical alloying.

In the past, small batches of amorphous metals have been produced through a variety of quick-cooling methods. For instance, amorphous metal wires have been produced by sputtering molten metal onto a spinning metal disk. The rapid cooling, on the order of millions of degrees a second, is too fast for crystals to form and the material is "locked in" a glassy state. More recently a number of alloys with critical cooling rates low enough to allow formation of amorphous structure in thick layers (over 1 millimeter) had been produced, these are known as bulk metallic glasses (BMG). More recently, batches of amorphous steel have been produced that demonstrate strengths much greater than conventional steel alloys.


Learning Objectives :

On completion of this topic you will be able to understand:

1. What is meant by metallic glasses.

2. The properties of metallic glasses

3. The various methods for producing metallic glasses.

4. Applications of metallic glasses.


Metallic glasses are a class of metallic alloys in which the crystallization process has been "frustrated" in some way, to the extent that a liquid-like, disordered long range atomic structure exists at temperatures well below the melting temperature of the alloy. Unlike the early metallic glasses which formed only under rapid solidification conditions (>1000's K/s), the highly stable bulk metallic glass alloys form at unusually low critical cooling rates (~1-10 K/s) and require no special processing to obtain their extraordinary mechanical properties.

clip_image002[4]

Computer simulation of the disordered atomic structure of a three- component metallic glass.


Properties

Amorphous metal is usually an alloy rather than a pure metal. The alloys contain atoms of significantly different sizes, leading to low free volume in molten state.Therefore they have therefore higher viscosity than other metals and alloys. The viscosity prevents the atoms moving enough to form an ordered lattice. The material structure also results in low shrinkage during cooling, and resistance to plastic deformation. The absence of grain boundaries, the weak spots of crystalline materials, leads to better resistance to wear and corrosion. Amorphous metals, while technically glasses, are also much tougher and less brittle than oxide glasses and ceramics.

Thermal conductivity of amorphous materials is lower than of crystals. As formation of amorphous structure relies on fast cooling, this limits the maximum achievable thickness of amorphous structures.

Amorphous alloys have a variety of potentially useful properties. In particular, they tend to be stronger than crystalline alloys of similar chemical composition, and they can sustain larger reversible ("elastic") deformations than crystalline alloys. Amorphous metals derive their strength directly from their non-crystalline structure, which does not have any of the defects (such as dislocations) that limit the strength of crystalline alloys.

One modern amorphous metal, known as Vitreloy, has a tensile strength that is almost twice that of high-grade titanium. However, metallic glasses at room temperature are not ductile and tend to fail suddenly when loaded in tension, which limits the material applicability in reliability-critical applications, as the impending failure is not evident.

Sample of Amorphous metal in the lab

clip_image002[6]

Perhaps the most useful property of bulk amorphous alloys is that they are true glasses, which means that they soften and flow upon heating. This allows for easy processing, such as by injection molding, in much the same way as polymers. As a result, amorphous alloys have been commercialized for use in sports equipment, medical devices, and as cases for electronic equipment.

Thin films of amorphous metals can be deposited via high velocity oxygen fuel technique as protective coatings.

The fatal drawback of plastics is their viscoelasticity behavior at a room temperature. So, when plastics are used as structural materials, they are normally reinforced with fiber reinforced plastic (FRP). However, in metal glass, since the glass transition temperature at which a viscoelasticity behavior becomes significant is much higher than room temperature and so problems due to viscoelasticity do not arise. Bulk glassy alloys also provide the outstanding moldability and high corrosion resistance as like plastics. Furthermore, since it is a metal, various functional characteristics: magnetic property, high strength and high toughness, are available.

They exhibit extraordinary physical, chemical, as well as mechanical properties, which result from their unique, disordered, atomic arrangements. Now amorphous alloys can be fabricated into bulk forms, ranging from several millimeters to several centimeters in thickness, by slow-cooling multicomponent alloy systems.

In particular, amorphous alloys tend to have low coercivity because there are no boundaries between crystalline grains to impede the motion of magnetic domain walls and because there is no magnetocrystalline anisotropy.

In this way, metallic glass can be regarded as a new material which has high moldability, high hardness and high toughness, and it can be used to make the micro scale industrial parts which could not be done with existing common crystalline alloys. The absence of grain boundary and dislocations are unique features of bulk glassy alloys making them suitable for using micro-scale parts fabrication.

They are not especially good conductors, due to their disordered atomic structure and high levels of alloying elements. It is sometimes assumed that metallic glasses, like common oxide glasses, are transparent to visible light, but this is not so. Photons at visible wavelengths are strongly scattered and absorbed by the conduction electrons in metallic glasses.

Although metallic glasses are electrically conductive, their resistance to current flow is generally higher than that of crystalline alloys. This helps to minimize eddy-current losses that occur due to rapid magnetization and demagnetization of the material.


Methods for producing Metallic glasses:

Chemical vapor deposition (CVD) is a chemical process used to produce high-purity, high-performance solid materials. The process is often used in the semiconductor industry to produce thin films. In a typical CVD process, the wafer (substrate) is exposed to one or more volatile precursors, which react and/or decompose on the substrate surface to produce the desired deposit. Frequently, volatile by-products are also produced, which are removed by gas flow through the reaction chamber.

Physical vapor deposition (PVD) is a variety of vacuum deposition and is a general term used to describe any of a variety of methods to deposit thin films by the condensation of a vaporized form of the material onto various surfaces. The coating method involves purely physical processes such as high temperature vacuum evaporation or plasma sputter bombardment rather than involving a chemical reaction at the surface to be coated as in chemical vapor deposition.

Melt spinning is a technique used for rapid cooling of liquids. A wheel is cooled internally, usually by water or liquid nitrogen, and rotated. A thin stream of liquid is then dripped onto the wheel and cooled, causing rapid solidification. This technique is used to develop metallic glasses that require extremely high cooling rates in order to form. The cooling rates achievable by melt-spinning are on the order of 104–107 Kelvin per second (K/s).

Rapid Quenching method: This method is used to extract heat from the melt by contact to a chill block. Cooling rate of the order of 106 K/s is required to form metallic glasses from the melt. Since fast extraction of heat is necessary, the dimensions of the solid obtained is limited to 50 µm. The molten liquid metal alloy is pushed out of a fine nozzle by gas pressure. A layer of rotating metallic disk is formed between the nozzle and the chill block. A mettalic glass ribbon about 1 cm wide, 30 µm thick can be thus produced.

Rapid quench flow instrument

clip_image002[8]

Solid- State Amorphization: Bulk metallic glasses that cannot be obtained by rapid cooling can be produced without going through a liquid phase.

1. When alloys are subjected to radiation such as electrons or ions, amorphization occurs.

2. A two-phase crystalline material gets converted into metallic glass through inter- diffusion when annealed at a moderate temperature.

3. Mechanical alloying also results in amorphization.

An ion implantation system at LAAS technological facility

clip_image002


Applications of Metallic glasses

Knife edges: The high hardness gives good wear resistance, and the lack of microstructure makes it possible to sharpen a very fine edge.

Springs: The combination of good resiliance and low damping makes metallic glasses exceptionally good springs. This may include some items that you don't necessarily think of as springs, including tennis rackets and golf clubs.

Fashion items: Metallic glasses can be polished to a fine finish, and good wear resistance means they don't scratch easily. This may make them attractive for jewelry and consumer electronics (such as cell phone cases). Plus, the perceived novelty is a selling point for many of these items.

Microelectromechanical systems (MEMS): These are highly miniaturized mechanical devices produced using specialized techniques originally developed for semiconductor processing. The high yield strain, low damping, and resiliance of metallic glasses makes them useful, for instance as hinges on micromirrors used for digital light processing technology.


Check your understanding

State whether True or False

1. Photons at visible wavelengths are strongly scattered and absorbed by the conduction electrons in metallic glasses.

Ans : True

2. They are especially good conductors, due to their disordered atomic structure and high levels of alloying elements.

Ans : False

3. Amorphous metal is usually an rather than a pure metal.

Ans : Alloy

4. The highly stable bulk metallic glass alloys form at very low critical cooling rates of ___?

Ans : 1-10 K/s

5. Why does an amorphous alloy has a low coercivity value?

Ans : In particular, amorphous alloys tend to have low coercivity value because there are no boundaries between crystalline grains to impede the motion of magnetic domain walls and because there is no magnetocrystalline anisotropy.


Summary

On completion of this topic you have learned

Metallic glasses are a class of metallic alloys in which the crystallization process has been "frustrated" in some way. The special features of metallic glasses has been projected in this topic. The various methods of preparing metallic glasses is described. Finally some of the applications are also listed out.


Activity

Find out the demerits of metallic glases.


Suggested Reading

1. Charles Kittel ‘Introduction to Solid State Physics’, John Wiley & sons, 7th edition, Singapore (2007)

2. M. Arumugam, ‘Materials Science’ Anuradha publications, Kumbakonam, (2006).


43 comments:

  1. Wonderful article, Which you have shared here about the glasses.
    These glasses are looking very beautiful and incredible in design.
    If anyone looking to buy any Prescription Glasses or
    Square Metal Frame Sunglasses
    i Love Glasses is the Best Online Store to Buy Glasses

    ReplyDelete
  2. Sunglasses are an essential type of assurance for anybody wandering outside. occhiali ciclismo professionisti

    ReplyDelete
  3. Another reason that kept metal casting technique alive is the low cost setup and implementation. Basically the process of metal casting is simple and need not require high skills. microfusione

    ReplyDelete
  4. Very nice article, I enjoyed reading your post, very nice share, I want to twit this to my followers. Thanks!. - päikeseprillid

    ReplyDelete
  5. Thanks for taking the time to discuss this, I feel strongly about it and love learning more on this topic. - päikeseprillid

    ReplyDelete
  6. Thanks for writing such a good article, I stumbled onto your blog and read a few post. I like your style of writing... gafas de sol de madera de bambu

    ReplyDelete
  7. first off, a hearty thanks to you. Your blog is awesome and completely knowledgeable and I completely satisfied with the reading. Keep your work spread till long after. For more Plastic Molding related information visit plastic mold & injection molding service.Certainly, you are Right!!

    ReplyDelete
  8. This is a great post. I like this topic.This site has lots of advantage.I found many interesting things from this site. It helps me in many ways.Thanks for posting this again. villas for rent in egypt

    ReplyDelete
  9. Hey what a brilliant post I have come across and believe me I have been searching out for this similar kind of post for past a week and hardly came across this. Thank you very much and will look for more postings from you. dubai properties for sale

    ReplyDelete
  10. You can likewise check for the specialist's credibility by surfing through his site and contrasting it and others. Then again, you can likewise spare thousands via doing the deal cycle without anyone else. Homes for sale in Calgary

    ReplyDelete
  11. Yes i am totally agreed with this article and i just want say that this article is very nice and very informative article.I will make sure to be reading your blog more. You made a good point but I can't help but wonder, what about the other side? !!!!!!Thanks costa sunglasses

    ReplyDelete
  12. I love the way you write and share your niche! Very interesting and different! Keep it coming! list of developers in dubai

    ReplyDelete
  13. There are 3 main classifications into which the education sector can be divided. They are: School education, Further education, and Higher education. Sometimes, education is carried out in a non-classroom background. It may take place in a prison or in a hospital. online math class

    ReplyDelete
  14. Your blog is too much amazing. I have found with ease what I was looking. Moreover, the content quality is awesome. Thanks for the nudge! Plot of Land for sale in Ibadan Nigeria

    ReplyDelete
  15. New web site is looking good. Thanks for the great effort. Apartments

    ReplyDelete
  16. Before we bounce into building a monetary model, we ought to ask ourselves what drives the business that we are investigating. The appropriate response will have critical ramifications for how we develop the model.
    Stump Removal Stockton

    ReplyDelete
  17. Presently how about we estimate a few adjusts identified with our first home loan. We should name this segment of the worksheet "First Mortgage" and beneath it add the accompanying details in the main segment: nova city developers islamabad

    ReplyDelete
  18. The stump that is left ought to likewise have some consideration as this can turn into an unattractive wreck for quite a long time to come. Tree Cutting professionals Syracuse

    ReplyDelete
  19. Do you get the picture now? This is exactly the reason why an expert in removing trees is needed. Tree Trimming services Albuquerque

    ReplyDelete
  20. Clearly, the landowner isn't the need of the US property the board organization, the occupants are.park view city housing scheme islamabad

    ReplyDelete
  21. This is one awesome blog. Really looking forward to read more. Really Great.
    Stump Removal Austin, TX

    ReplyDelete
  22. Tragically the significant destinations realestate.com.au and domain.com.au don't permit private merchants to list their houses available to be purchased. los angeles condos for rent

    ReplyDelete
  23. Tajarat strives to be Pakistan's biggest real estate developer ever, guaranteeing the highest international standards, prompt execution, and lifetime customer loyalty. For further detail visit lahore smart city payment plan

    ReplyDelete
  24. I definitely enjoying every little bit of it. It is a great website and nice share. I want to thank you. Good job! You guys do a great blog, and have some great contents. Keep up the good work. occhiali da vista burberry donna

    ReplyDelete
  25. The JMS informing motor is incorporated into the application server. This is an unadulterated java informing motor. https://www.blackmartappdownloads.com/

    ReplyDelete
  26. I am happy to find this post Very useful for me, as it contains lot of information. I Always prefer to read The Quality and glad I found this thing in you post. Thanks New lenox real estate agents

    ReplyDelete
  27. which is a sensible grouping for experience. Notwithstanding, it would be challenging to move from building one step at a time (foundation) to the powerful action of a point since structure would will quite often oppose the commencement of a new thing. The cadent houses overcome this issue between the laying out head of one gathering of three houses (quadrature). furthermore the powerful head toward the start of the following gathering of three houses (quadrature). Utilizing this reasoning:
    Silk bed sheets

    ReplyDelete
  28. https://www.buyyoutubesubscribers.in/2021/12/30/how-hide-subscribers-youtube/ If you are aiming to boost views on YouTube for all the videos you have uploaded, then you have to keep in mind that there are a lot of methods available for you. Being aware of those methods that can boost traffic to your site can definitely help you out in obtaining massive exposure. Here are few of the methods that you can try:

    ReplyDelete
  29. https://www.visualaidscentre.com/lasik-eye-surgery-in-delhi/ Perhaps, the biggest advantage to making your own YouTube videos is that your videos can be just about whatever you want them to be. Popular videos on YouTube right now include comedy skits, video blogs, how-to videos, and music videos from up and coming artists.

    ReplyDelete
  30. After a long time, I read a very beautiful and very important article that I enjoyed reading. I have found that this article has many important points, I sincerely thank the admin of this website for sharing it.Best scale parts service provider

    ReplyDelete
  31. The U.S. citizenship test is an examination administered by U.S. Citizenship and Immigration Services (USCIS) to determine whether an applicant for naturalization meets the basic knowledge and understanding of U.S. history and government required to become a citizen. The test consists of 10 civics questions, which cover topics such as the U.S. Constitution, the Bill of Rights, and the branches of government. Applicants must answer at least six out of 10 questions correctly to pass the test. us.citizenship test

    ReplyDelete
  32. This comment has been removed by the author.

    ReplyDelete
  33. new flats for sale near shamshabad The Aparna Group is considered the "leader of the future" of real estate because of the superior projects it has delivered over the course of its more than two decades in the business.

    ReplyDelete
  34. This comment has been removed by the author.

    ReplyDelete
  35. B18 alludes to the ongoing year's property deal esteem.
    cash buyers Philadelphia

    ReplyDelete
  36. That's what this equation expresses in the event that the ongoing year (B12) is equivalent to our investment period ($B$10) our deal cost will be equivalent to our projected property estimation in that specific year (B14).
    https://www.districtrealty.com/

    ReplyDelete
  37. You ought to be allowed to work with your seller of decision for your IRA's buy.
    what is a precious metals ira

    ReplyDelete
  38. "The real estate market can vary significantly from region to region, so it's important to understand local trends." http://spencerp.net/

    ReplyDelete
  39. I've been thinking about investing in real estate lately. The potential for passive income through rental properties is really appealing, especially in a market with high demand. estate planning chandler

    ReplyDelete
  40. In a world of fast-paced technology, a lorgnette is a slow dance with elegance. Best Under $100 Binoculars

    ReplyDelete
  41. Your blog post is a literary ballet, where every word pirouettes with grace, orchestrating a symphony of intellect and emotion. The narrative twirls through the intricate choreography of profound insights, leaving readers captivated in its rhythm. It's not just a post; it's a performance that gracefully resonates, inviting the audience to be enthralled by the beauty of your ideas.

    ReplyDelete
  42. Intriguing piece Your thoughtful insights and expressive storytelling create a captivating reading experience. I appreciate the blend of facts and personal touch, making it relatable and informative. Your ability to convey complex ideas with clarity is commendable. Eagerly anticipating more compelling content from your blog. Keep up the excellent work

    ReplyDelete
  43. Blogging is something I do routinely, and I genuinely appreciate the quality of your content. This compelling article has grabbed my attention. I've added your website to my bookmarks and plan to stay updated with the latest details, typically on a weekly basis. Moreover, I've subscribed to your RSS feed. Traveling to Azerbaijan visa requirements for german citizens entails meeting visa prerequisites such as a valid passport, completed application, passport photos, travel plans, and accommodation confirmation. E-visas offer a hassle-free option for application.

    ReplyDelete